U-Sand® Pro-Sander

daily: $45 • weekly: $185 • monthly: $525

Write a Review
Millersburg - (330) 674-5533
Sugarcreek - (330) 852-3600
Mt. Vernon - (740) 397-7368

 

U-Sand® Pro-Sander
Please note:
 

There is a 10% damage surcharge on all rentals.
Ask about available commercial exemptions.

 Sanding floor machines can be bulky, balky, and damage hardwood floor finishes if used incorrectly.  At Holmes Rental, we’ve taken renting floor sanding equipment to a new level. Using four-pad, random orbit technology, the U-Sand Pro sander makes floor sanding easy and worry-free by eliminating the possibility of damaging the floor.The U-Sand Pro is 40 lb. lighter than the original U-Sand and offers a more aggressive cut.  Acting as a sander, edger and buffer, this machine can complete a flooring job from start to finish.

Features:

Three pieces of hardwood floor sanding equipment in one:

  • Floor Sander
  • Floor Edger
  • Floor Buffer

 Great in light spaces: Closets, bathrooms, hallways, kitchens, foyers

Benefits of the U-Sand Pro Sander

U-Sand changes everything about floor sanding.

Rip and strip finishes on existing floors with ease.  Cuts through urethane efficiently and leaves the wood clean and ready for a new finish.  Sands in any direction without damaging the grain pattern, and is the best machine for antique floors as it removes far less material than drums so your floors last longer. 

Far easier to use than traditional drum sanders: change hook and loop grit disks in seconds, vacuums dust out of the way as you go, edge and buff with the same machine, floats easily as you make your passes.

OPERATOR SAFETY INSTRUCTIONS

COMMERCIAL USE

 

For the safe operation of this machine, read and understand all warnings and cautions. Look for this symbol:

“WARNING”: If you do not follow the instructions in a WARNING, injury can occur to you or to other personnel. “CAUTION”: If you do not read and follow instructions   completely, damage can occur to the machine.

 WARNING: You must be qualified for the operation of this machine before using it.

READ THE INSTRUCTION MANUAL.

WARNING: Machines can cause flammable materials and vapors to burn. Do not use this machine with or near matches, fuels, grain dust, solvents, thinners, or other flammable materials.

 WARNING: Do not use on wet surfaces.

 WARNING: Risk of explosion. Floor sanding can result in an explosive mixture of fine dust and air. Use floor sanding machine only in a well- ventilated area.

WARNING: Do not allow machine to be used as a toy. Close attention is Necessary when used by or near children.

WARNING: Use only as described in this manual. Use only manufacturer’s   recommended attachments.

WARNING: Do not use with damaged cord or plug. If machine is not working as it should, has been dropped, damaged, left outdoors, or dropped into   water, return it to the rental center. 

WARNING: Do not leave machine when plugged in. Unplug from outlet when not in use and before servicing.

WARNING: Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

WARNING:   Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

WARNING: To prevent injury, always remove the electrical plug from the electrical outlet before changing the sandpaper, emptying the bag, leaving the machine, or doing any maintenance to this machine.

WARNING: Do not handle plug or machine with wet hands.

WARNING: Do not put any object into vacuum openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

WARNING: Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

WARNING: Turn off all controls before unplugging.

WARNING: Do not use machine to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be pre sent. 

WARNING: To prevent fire explosion when emptying the dust bag:

  1. Remove the contents of the dust bag when the bag is 1/3 full.
  2. Remove the contents of the dust bag each time you finish using the machine.
  3. Do not put the contents of a dust bag into a fire.

WARNING: Do not use machine without proper dust bag. Black Bag with yellow writing and Fire Lock Logo US-VBAS14.

WARNING: To prevent damage to the power cable, do not let the sandpaper touch the power cable when the machine is running. Always lift the power cable over the machine. 

GROUNDING INSTRUCTIONS

 This machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING:         Improper connection of the equipment-grounding conductors can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not, modify the plug provided with the machine-if it will not fit the outlet, have a proper outlet installed.

This machine is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug illustrated in sketch A in Figure 1. A temporary adapter that looks like the adapter illustrated in sketches B and C may be used to connect this plug to a 2-pole receptacle as show in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a qualified electrician can install a properly grounded outlet (sketch A). The green colored rigid ear, lug, or the like extending from the adapter must be connected to permanent grounds such as a properly grounded outlet box c over. Whenever the adapter is used, it must be held in place by a metal screw.

  WARNING:         Always use this machine with an AC three conductor electrical system connected to the electrical ground. Replace any worn, cut, or damaged cords. Replace damaged plugs, receptacles or connector bodies.

 WARNING:         Do not cut, remove or break the ground terminal. Do not try to fit a three-terminal plug into a receptacle or connector body that does not fit the plug. If the receptacle or connector body does not fit the plug, have a qualified electrician make the connection.

 WARNING:         Do not move the machine over an electrical cord. Always lift the cord over the machine.

 WARNING:         To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands. 

EXTENSION CORDS

 Use only 3-wire extension cords that have 3-prog grounding-type plugs and 3-pole cord connectors that accept the plug from the product. Use only extension cords that are intended for extra-hard service.

These extension cords are identified by a marking such as “S, SO, ST, or STO”. Use only extension cords having an electrical rating no less than the rating of the product. DO not use damaged extension cords. Examine the extension cords before using, and replace if damaged. Do not damage the extension cord and do not pull on any cord to disconnect. Keep the cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord. 

BACKER PAD/DUST SKIRT INSTALLATION

 Use ¾” open end wrench to hold lower shaft and turn backer pad clockwise to install.

  1. HAND TIGHTEN ONLY!
  2. Set machine upright on floor.
  3. Attach the removable part of the dust skirt (US115-146) to the lower part of the deck plate so that the skirt just touches the floor. (if not properly installed the vacuum system may not operate to its full potential).

INSTRUCTIONS

 WARNING:

  1. Make sure the Sander switch is in the OFF position before you plug the unit in.
  2. Never change the sandpaper while the sander is plugged in.
  3. Check breaker circuit to be used, 20 amp is the minimum required.
  4. Always wear eye protection, ear protection and dust mask while operating the sander.
  5. Empty the vacuum system in an area away from flammable materials and flame or fire.

TOOLS NEEDED 

  1. Hammer
  2. Pry bar; to remove trim
  3. Paint scraper; to scrape corners and hard to reach places.
  4. Nail set
  5. Vacuum system; using a 1.5” ID vacuum hose to collect dust created by sanding process.
  6. Plastic draping; to cover and isolate work areas.
  7. Masking tape
  8. Wood filler
  9. Mineral spirits and or tack cloths; to remove fine dust particle prior to coating floor with finish. 

ROOM SETTING AND FLOOR CHECK

  1. Remove all existing furniture, carpets, floor mats, clutter, and curtains from the area to be sanded. Sweep the floor thoroughly.
  2. Remove all nails, and metal fasteners that protrude from the surface to be sanded. These items may damage sanding pads, sandpaper or prevent effective sanding.
  3. Check for cracks and niches in the area to be sanded and repair damaged areas. Excessive damage may be repaired with wood filler (allow sufficient drying time). Follow wood filler manufacture instructions for use.
  4. Put dust protection on all doorways and heat vents in the form of drop cloths and plastic sheets. Vacuum the room thoroughly.

CHECKING CONDITIONS OF THE FLOOR

Check for condition of floor using one of the following tests and follow appropriate directions:

Wax Floor:

Place a damp cloth (approx. 18” x 18”) on the floor. Lift after an hour and check for any cloudy coloration. A white cloudy coloration indicates wax. In this case, strip the wax using a wax stripper before sanding is attempted. Excess wax will clog the sandpaper.

Painted Floor:

Chemically remove paint before attempting to sand floor. 

Varnished Floor:

U-Sand® equipment will remove most kinds of varnish. Excessive layers of varnish, however, may require chemical removal before attempting to sand the floor. 

Unfinished Floor:

Start the sanding process with the least aggressive grit as possible, progressing to the finer grits of sandpaper ranging from 24 grit (the most aggressive/coarse) 36, 40, 60, 80, 100, 120 grit (less aggressive, coarse). Etc. 

OPERATING THE U-SAND® EQUIPMENT

WARNING:         Always remove the electrical plug from the electrical outlet before installing and changing the sandpaper.

Select the paper to start:

Select the least aggressive grit as possible that removes the desired amount of surface. Too aggressive grits leave swirl marks that are difficult to remove with finer grits that will be used later. Grits that are not aggressive enough do not take enough of the surface off and result in more work and a slower process

Installing Paper:

Sandpaper should be installed by leaning the machine back and placing the sandpaper on the backer pads (BP6).

Changing Sandpaper:

Paper should be changed when you notice less pull when running the equipment and see less material being removed by the process (10-15 minutes).

CAUTION:To prevent damage to backer pads, you must change sandpaper when it becomes loaded or clogged. 

STARTING THE SANDING PROCESS

Before operating the machine, make sure the handle adjusting lever is tight.

Empty the vacuum system when full into a metal canister away from your workspace and other Flammable materials (this may need done several times during the process).

Remove the vacuum system from the unit when not in use and empty contents as instructed above.

STEP 1:

Determine the condition of the floor. We recommend staring with 36 grit (24 grit for severely damaged or heavy polyurethane floors). Lean the machine back on its handle. Attach the sandpaper to the backer pads. Sandpaper usage will depend on the finish to remove, and the amount of wood that needs to be removed.

STEP 2:

With the U-Sand® equipment in the upright position, turn the switch on and slowly move the sander over the floor, letting the machine do the work for you. For new installation it is recommended to move the machine across the grain, this is the most effective way to level the floor. (change sandpaper when it appears plugged or dull).

Proper Grit Sequence:

24 if needed

36 for leveling

40 sand thoroughly

80 final sanding and clear finish 120 recommended for staining

STEP 3:

After sanding the floor completely, with the first grit, vacuum the floor thoroughly and change paper to the next finer grit. Continue the sanding process. Check paper after sanding about a 10’ x 10’ area to see that the paper is still sanding. Inspect the floor to see if any swirl marks remain. If swirl marks exist, continue to sand just the area with the higher grit paper until they are less visible. You should get down close to the floor and view it from several directions in good light for this inspection.

STEP 4:

Use progressively higher grits. Sand the floor completely. This step will take less time than the previous grits. Check sandpaper often to make sure it is clean and effective.

STEP 5:

Inspect the floor thoroughly for scratches or unevenness. Apply the final finishing grit (usually 120 or 180 grit). At this point, the floor should become smooth and free of all swirl marks when inspected closely.

STEP 6:

Corners and edges and be sanded with a detail sander or hand scraper. A paint scraper can be used for hard to reach areas, such as: under radiators, and in corners. Some hand sanding may be necessary in these remove places. Inspect the floor thoroughly to determine when you are finished sanding

STEP 7:

Vacuum the floor and clean with a tack cloth (available at your local hardware store). Then apply stain or varnish as desired. Follow manufacturer’s recommendations for staining and finishing.

WARNING: Machines can cause Flammable materials and vapors to burn. Do not use this machine with or near matches, fuels, grain dust, solvents, thinners, or other flammable materials. 

WARNING: To prevent injury always remove the electrical plug from the electrical outlet before changing the Sandpaper, emptying the bag, leaving the machine, or doing any maintenance to this machine.

REMOVING THE DUST BAG:

Unlock the Velcro straps and then remove the dust tube from blower. Empty the bag into a metal or non-flammable container away from your work area. DO NOT LEAVE DUST BAG ON THE UNIT WHEN NOT IN USE. Remove from machine when not in use for two (2) minutes or more and store in a metal container away from flammable objects. DO NOT TRANSPORT MACHINE WITH DUST BAG ATTACHED. Remove from unit, empty and carry separately.

ADJUSTING THE HANDLE POSITION

Loosen the black knob (US146-146) and then adjust the handle position as desired. Tight the black knob once adjusted.

PROPER STORAGE OF THE POWER SUPPLY CORD

 Wrap the power cord around the frame of the machine for storage. Then, adjust the handle to the lowest position and store machine in and upright position.  

CLEANING AND STORAGE 

Remove the dust system from the unit. Discard contents away from work area in a non-flammable area. Wipe the exterior of the unit with a damp cloth. Leave the last grit of sandpaper on the backer pads for transport and storage. This will protect the hook and loop of the backer pads.